Which battery charger should you use?

Today there are many different types of phones on the market. So getting in trouble with the charger is inevitable. Here are some tips to help you choose a good battery charger.
– First, Use smart charger! A cheap charger can not tell you when the battery is full, or whether it is charging it out (quickly after use) or charging it (causing battery damage). Make sure you have a good charger.
– Second, Charge both NiMH and NiCd batteries. Most of the battery chargers produced after 2005 are both rechargeables. Some newer chargers will only charge NiMH batteries since NiCd batteries are less common. You can choose the best 18650 battery charger.

best 18650 battery charger
– Third, Old NiCD chargers are usually not good with NiMH batteries. Old NiCD charger can not tell you when to stop charging NiMH batteries. And if it is badly charged, it will charge (missing or overcharged) your battery.
– Fourth, All of the chargers of this company can recharge the battery of another company. For example, Panasonic chargers can charge Sony batteries or vice versa. You only need to make sure that the correct type of battery (eg NiMH batteries have to be recharged with NiMH), and the charger brand does not matter. Of course, I still recommend using a good, smart charger.
– Fifth, Low-charge NiMH (LSD) batteries like Eneloop do not require special charging. Any NiMH charger can charge NiMH batteries.

best 18650 battery charger2
– Finally, NiZn batteries need a special charger. And both NiMH and NiCD can not be used for this type of battery.
There are many types of chargers, and most likely, do not break off when the battery is full or shut off too soon, too late, or off – continue charging until you remove the battery from the charger. This is bad, because charging low will cause your battery to not have enough space to use as a battery, and overcharging will reduce the battery life (the number of charges). A good charger gives the battery exactly the capacity it needs. There are three types of chargers:
– Poor charging (users have to adjust, disconnect power). This charger does not automatically stop. The user guide will tell you when you have to remove the battery from the charger for each type of battery, and you have to remove the battery after the time. Because each battery is different, no matter how careful you are, you will either overcharge or overcharge your battery.
– Charging prescribed time. This charger has a meter and switches itself off after a specified amount of time, which means that you are almost certainly not going to be charged enough or too full. Some of the breaker clocks of the charger are set up with very long interruptions, so often the batteries are overcharged. Some chargers with a more reasonable clock will reduce the charge rate too – but not completely eliminated: if you charge the battery when not in use, the battery will be charged too. And sometimes the battery loses capacity, the charger with this timer will continue to charge when the battery is full.

best 18650 battery charger2
– Good and smart charger. This charger recognizes itself when the battery is full and automatically disconnects. The methods used are usually to measure the tip of the voltage, the maximum voltage, the rate of change of heat, the maximum heat, or combine them together. Watches are sometimes used as a secondary mechanism, making sure that charging does not interrupt the signal from other methods. “Smart” charger means more important: smart chargers charge the batteries independently, giving each battery exactly the energy it lacks.
The good news is that in the market, the price of the smart charger and rechargeable batteries are often equal. Therefore, you should become a smart consumer. This information is useful. So choosing the best charger for yourself is not a difficult problem for you. Good luck to you.

What is wet vacuum cleaner

The wet vacuum cleaner sucks liquid water inward through the nozzle and suction pipes. It carries a very dense filter and a float, which stops the motor when it reaches a certain level of aspirated liquid. What interests us most is that the vacuum cleaner leave the area as dry as possible. It has a suction that can be fixed.The additional accessories that go with the wet vacuum cleaners are flat nozzle, brush nozzle, slit, for furniture, for radiators, (for vacuum cleaners).

How to use wet vacuum cleaner:
● Make sure the filter and dust bag are removed
● Make the boiler empty of any dust and dirt
● Connect the hose to the machine
● Plug it into the wall socket
● Turn on the machine by pressing the switch or rotate (depending on type)
● After use, throw empty the boiler and do not close the machine immediately but dry it first!

Tip! Never suck flammable liquids and foaming liquids.

To boot the water and dirt from the surface, the vacuum cleaner need to have a great power of absorption. To do this we reduce the diameter of the accessories, thereby decreasing the flow. We recommend a vacuum cleaner with high power, above 2100 millimeters of water column (H2O C. mm) for the professional use in industry. Therefore, if you just want one for your home, opt for a smaller with a lower power one. For example, pot for a compact devices for sucking up dust or water – A wet vacuum cleaner with an air flow rate of 180 to 360 m3 / hr, motor 230 V which is standard equipped with hose 3m, S-tube, flat suction nozzle and brush or squeegee suction nozzle and suction of 2200 mm water column. This kind of machine often go with some accessories such as brush nozzle, small rug suction nozzle, squeegee (diameter 40 mm), or an extra hose of 3 m Ø 40 mm connector
Maintenance tips for the wet vacuum cleaner

Vacuum cleaners are fast and easy to maintain. They should provide years of useful service. It is worth taking a few minutes to change the bag and check the filter regularly to keep them running with guarantee.

To maintain the wet vacuum cleaner condition, you have to replace the dust bag when it is full and clean the dust filter or water or mixed, check that the cable has no cracks and clean the machine and accessories. To save the tubes and nozzles which are separated, try not to excessively bend the hose and roll up the power cord. Here are steps to clean the wet vacuum cleaner:

A. Change or empty the bag when it is filled. Performs this task outdoors or in a well ventilated area and respects the manufacturer’s instructions.

B. Check the filter regularly and change it when necessary according to the manufacturer’s instructions. Check that no vacuum residue to function effectively.

C. Check the brush with periodicity. Remove the pieces of thread or hair that accumulate in the brushes.

D. If it is not suckling well, it is possible that the vacuum tube is stuck. To unclog, drop of the housing and see that there is nothing inside, there are also times when the jam occurs at the junction with the housing.
Want some wet and dry vacuum cleaner?

Wet and dry vacuum cleaners

WHAT SHOULD I USE TO DRY SUCK? In dry vacuuming, there will always be round filter mounted and we strongly recommend the use of a dust bag.

WHAT SHOULD I USE FOR WET VACUUM? When wet vacuuming, we recommend to remove the circular filter. Also, the dust bag must be removed.

MACHINE STOPS WITH WET VACUUM. The boiler is filled with water. This allows the float touches the vacuum motor and no longer vacuum sucked.

MACHINE STOPS QUICKLY WITH WET VACUUM? Check that the round filter is removed. If it is not removed it will be too high, so that this vacuum is sucked against the motor and the machine (earlier) stops sucking.

I CAN NOT SUCK WITHOUT DUST BAGS? The filter will be very quickly are full of dust when not used dust bag. If the filter “pass” and (construction) dust in the engine will void the warranty.